--- title: "TP.V56.PB826 firmware dump for ULTRA UT320. fix it now!" url: "https://tvtech.online/tp-v56-pb826-firmware/" author: "belmmahi" published: "2026-09-11T14:42:24+00:00" modified: "2026-09-11T16:02:45+00:00" language: "en-US" site: "TV TECH" --- Source: https://tvtech.online/tp-v56-pb826-firmware/ TP.V56.PB826 Firmware Dump – ULTRA UT320 SPI Flash Download | TV Tech For Technician Use Only # TP.V56.PB826 Firmware Dump for ULTRA UT320 – SPI Flash Memory Repair Download By **TV Tech Online** September 11, 2026 Verified Dump Firmware Dump This technical resource provides a **tested and verified SPI flash firmware dump** for the **TP.V56.PB826** main board installed in **ULTRA UT320** television sets. The dump targets the **GD25Q32B** memory IC and is designed to resolve critical boot and display failures caused by corrupted flash data. This file is intended exclusively for qualified TV repair technicians. Firmware Tested – 100% Working ## Hardware Specifications | Brand | ULTRA | | --- | --- | | Model | UT320 | | Main Board | TP.V56.PB826 | | Panel | HV320WHB-N85 rev1.0 BOE | | SPI Flash IC | GD25Q32B (32Mbit / 4MB) | | Programmer | SP8-A / SP8-B Universal Programmer | | Dump Status | Tested and Verified Working | | File Format | .bin (Raw SPI Dump) | ## Main Board Identification Before proceeding with any firmware flash operation, confirm your main board matches the **TP.V56.PB826** revision shown below. Verify the board silkscreen markings, component placement, and connector layout. Flashing an incorrect dump to a different board revision may cause permanent hardware damage. TP.V56.PB826 main board – click image to zoom in new tab ## SPI Flash Chip Location The **GD25Q32B** SPI flash chip is located near the main processor on the TP.V56.PB826 board. It is an 8-pin SOIC package. Use a hot air station set to 320 degrees Celsius with moderate airflow to desolder the chip safely. Avoid overheating adjacent components, particularly the main IC and crystal oscillator. SPI GD25Q32B chip location on TP.V56.PB826 – click to zoom in new tab ## Common Issues This Firmware Resolves The following symptoms on the ULTRA UT320 with TP.V56.PB826 main board typically indicate corrupted SPI flash memory data requiring a fresh dump write: 1. **Stuck on boot logo** – TV powers on, displays the ULTRA logo, and freezes without progressing to the home screen or input source 2. **Black screen with backlight active** – Backlight LEDs illuminate but no picture or OSD appears on screen 3. **Complete no-boot condition** – Power LED blinks or remains solid but the TV produces no display output whatsoever 4. **EEPROM and channel data corruption** – All saved channels, settings, and user preferences are lost repeatedly after power cycles 5. **OSD menu freeze or partial display** – On-screen display appears garbled, freezes mid-navigation, or shows corrupted text and icons 6. **Automatic restart loop** – TV boots, briefly shows an image, then restarts continuously without user input 7. **No audio output with distorted picture** – Video signal appears with artifacts while audio output is completely absent 8. **Input source not detected** – HDMI, AV, and USB inputs fail to respond or are not listed in the source menu ## Diagnostic and Repair Protocol Follow this step-by-step protocol to ensure a successful firmware flash operation on the TP.V56.PB826 main board: 1. **Visual Inspection** – Examine the main board for obvious physical damage including burnt components, swollen capacitors, cracked solder joints, and liquid damage indicators 2. **Power Supply Verification** – Measure all output voltages from the power supply board. Confirm 5V, 12V, and 3.3V rails are within 5 percent tolerance before proceeding 3. **SPI Chip Removal** – Desolder the GD25Q32B using a hot air rework station at 320 degrees Celsius. Apply quality flux and use a preheater if available to reduce thermal shock risk 4. **Chip Preparation** – Clean the SPI chip pads and socket adapter pins with isopropyl alcohol. Inspect the chip under magnification for damaged pins or cracked packaging 5. **Read Original Data** – Place the chip in the SP8 programmer SOIC8 adapter. Perform a full read of the existing data and save it as a backup file before writing 6. **Write Firmware Dump** – Load the downloaded .bin firmware file into the SP8 software. Execute Erase, Program, and Verify operations in sequence. Ensure verification passes with zero errors 7. **Resolder SPI Chip** – Carefully resolder the chip back to its original position on the main board. Verify solder joints under magnification and check for bridges between pins 8. **Functional Test** – Reconnect the panel flex cable, power supply, and speaker. Power on and verify boot sequence, OSD functionality, all input sources, and audio output 9. **Final Calibration** – Perform factory reset from the service menu. Adjust white balance if required for the HV320WHB-N85 panel. Run channel auto-scan to confirm tuner operation ## Video Repair Guide ## Download Firmware Dump ## TP.V56.PB826 – ULTRA UT320 SPI Dump Verified firmware dump file for GD25Q32B flash memory. Compatible with SP8 universal programmer. File: TP.V56.PB826_UT320.bin | Size: 4 MB | IC: GD25Q32B **Step 1:** Click to verify access **Step 2:** Download firmware file Download Firmware Dump ## Frequently Asked Questions What programmer is needed for TP.V56.PB826 SPI flash? Use an SP8-A or SP8-B universal programmer with a SOIC8 test clip or adapter socket to read and write the GD25Q32B SPI flash chip on the TP.V56.PB826 main board. Ensure your SP8 software is updated to the latest version for correct chip recognition. Is this TP.V56.PB826 firmware dump tested? Yes, this firmware dump has been tested and verified 100% working on the ULTRA UT320 with panel HV320WHB-N85 rev1.0 BOE. The dump was read from a fully functional unit and validated through multiple write and verify cycles. What issues does this firmware fix? This dump resolves stuck logo, black screen with backlight, no boot, EEPROM corruption, channel loss after power failure, OSD freeze, restart loops, missing audio, and input source detection failures on the ULTRA UT320 with TP.V56.PB826 board. Can I use this dump on a different panel model? This dump is calibrated specifically for the HV320WHB-N85 rev1.0 BOE panel. Using it with a different panel may result in incorrect gamma, inverted colors, or no display output. Always match both the main board and panel model before flashing. ### Related Firmware Downloads - [Browse All Firmware Dumps](https://tvtech.online/category/tv-dumps/) - [TP.V56 Series Main Board Firmware Collection](https://tvtech.online/category/china-tv/) - [SP8 Programmer Setup and Usage Guide](https://tvtech.online/?p=2407) - [SPI Flash Memory Repair Tutorial for Beginners](https://tvtech.online/category/spi/) **Technician Disclaimer:** This firmware dump is provided for professional TV repair technicians only. Incorrect use may result in permanent damage to the main board or panel. Always back up the original SPI data before writing. Verify board model, panel compatibility, and SPI chip type before proceeding. TV Tech Online assumes no liability for damages resulting from improper use of this file. Share: