FOR TECHNICIAN USE ONLY — PROFESSIONAL FIRMWARE RESOURCE
Firmware Dump File
TP.SIS231.P63 Firmware Dump
Goldvision GVLED 24M3F TNT
Tested SPI 25Q32 memory dump for resolving flash corruption and boot failure. Professional repair resource.
Updated: 01 September 2026
TP.SIS231.P63
100% Tested
Professional Technicians Only
This firmware dump file is intended exclusively for qualified electronics repair technicians. Improper flashing may permanently damage the main board. Proceed with proper equipment and knowledge.
Firmware Specifications
| Brand | Goldvision |
| Model | GVLED 24M3F TNT |
| Main Board | TP.SIS231.P63 |
| Panel | V236BJ1-XC01 |
| SPI Flash Memory | 25Q32 (32Mbit / 4MB) |
| Programmer Method | SPI8 |
| Status | Tested 100% Working |
Known Issues for GVLED 24M3F TNT
The following symptoms indicate SPI flash memory corruption on this model and can be resolved by re-flashing the firmware dump:
- TV stuck on logo screen — fails to boot past the Goldvision splash
- Continuous restart loop — power cycles repeatedly without reaching main menu
- Black screen with backlight ON — panel illuminates but no OSD or image appears
- No signal on all input sources — HDMI, AV, and USB inputs unresponsive
- Main menu freezes or shows corrupted on-screen display graphics
- Sound works but no picture — audio output present with blank display
- Dead set after failed software update — bricked after OTA or USB update attempt
- Channel auto-scan failure — tuner cannot detect or store TNT channels
Diagnostic and Repair Protocol
Pre-Repair Diagnostics
Visual Inspection
Examine the TP.SIS231.P63 main board for burnt components, swollen capacitors, or damaged traces around the SPI flash area.
Power Supply Verification
Confirm all voltage rails are within specification: 5V standby, 12V main, and 3.3V logic supply to the SPI chip must be stable.
SPI Chip Identification
Locate the 25Q32 SPI flash chip on the board. It is typically an 8-pin SOIC package near the main processor.
Firmware Flashing Procedure
Download Firmware File
Download the verified SPI dump file using the secure download button below. Extract the .bin file from the archive.
Connect SPI Programmer
Attach your SPI8-compatible programmer (CH341A recommended) to the 25Q32 chip. You may flash in-circuit or remove the chip for out-of-circuit programming.
Erase Existing Data
Perform a full chip erase to clear all corrupted data from the 25Q32 memory before writing.
Write Firmware Dump
Load the downloaded .bin file into your programmer software and write it to the chip using the SPI8 protocol.
Verify Written Data
After writing, run a verification pass to ensure the flashed data matches the source file with zero errors.
Reassemble and Power Test
Reinstall the chip (if removed), reassemble the TV, and power on. The Goldvision GVLED 24M3F TNT should boot normally, displaying the setup wizard or last saved configuration.
Video Tutorial
Download Firmware Dump
File TypeSPI Flash Dump (.bin)
Target Chip25Q32 (4MB)
BoardTP.SIS231.P63
MethodSPI8 Programmer
CompatibilityGoldvision GVLED 24M3F TNT
Click once to proceed — download starts on second confirmation.
Frequently Asked Questions
What SPI chip is used on the TP.SIS231.P63 board?
The TP.SIS231.P63 main board uses the 25Q32 SPI flash memory chip, which is a 32Mbit (4MB) serial NOR flash in an 8-pin SOIC package.
What programmer method is required?
Use the SPI8 programming method. The CH341A USB programmer with the appropriate SOIC8 clip is the most commonly used and reliable tool for this operation.
Is this firmware dump tested and verified?
Yes. This firmware dump has been extracted from a fully functional Goldvision GVLED 24M3F TNT unit and has been tested and verified as 100% working on the TP.SIS231.P63 main board with V236BJ1-XC01 panel.
Can I flash this firmware using USB instead of a programmer?
No. This is a raw SPI memory dump file, not a USB update package. It must be written directly to the 25Q32 chip using an SPI programmer. USB flashing requires a different file format provided by the manufacturer.
